Listing 1 - 10 of 65 | << page >> |
Sort by
|
Choose an application
Surveying the technologies used to satisfy the world's demand for open, efficient, and clean electricity, Variable Speed Generators provides an in-depth examination of variable-speed generators for both stand-alone and grid-connected applications. Part of The Electric Generators Handbook, Two-Volume Set, this work offers authoritative, tightly focused treatment of the topologies, steady state and transients modeling, performance, control, design, and testing of stand-alone and grid-connected generators operating at variable speeds. Variable Speed Generators thoroughly covers all types of variable-speed generators currently in progress in distributed generation and renewable energy applications around the world. It delves into the steady state, transients, control, and design of claw-pole rotor synchronous, induction, permanent magnet-assisted synchronous, and switched reluctance starter alternators for hybrid-electric vehicles. It also discusses PM synchronous, transverse-flux PM, and flux-reversal PM generators for low-speed wind and hydro energy conversion as well as linear-motion alternators for residential and spacecraft applications. Numerous design and control examples illustrate the discussion. The promise of renewable, sustainable energy rests on our ability to design innovative power systems that are able to harness energy from a variety of sources. Variable Speed Generators supplies the tools necessary to design, validate, and deploy the right power generation technologies to fulfill tomorrow's complex energy needs.
Choose an application
Variable speed drives. --- Variable speed drives --- Standards.
Choose an application
Variable speed drives. --- Variable speed drives --- Standards.
Choose an application
AC adjustable speed drive (ASD) systems rated above 375 kW and above 750 V output voltage as used in petrochemical and similar applications are applicable to this standard. Performance requirements for an ASD system including, but not limited to, input transformer or reactor as required, power electronics, control interfaces, cooling system, switchgear, and motor are covered. Requirements for power quality, engineering analysis, start-up assistance, training, and spare parts are also included. Certain items such as the motor, switchgear, or transformer may be excluded from the scope of vendor supply if specified in the data sheets; any special requirements for the excluded equipment shall be given by the system vendor. Keywords: adjustable speed, IEEE 1566, large drives.
Choose an application
AC adjustable speed drive (ASD) systems rated above 375 kW and above 750 V output voltage as used in petrochemical and similar applications are applicable to this standard. Performance requirements for an ASD system including, but not limited to, input transformer or reactor as required, power electronics, control interfaces, cooling system, switchgear, and motor are covered. Requirements for power quality, engineering analysis, start-up assistance, training, and spare parts are also included. Certain items such as the motor, switchgear, or transformer may be excluded from the scope of vendor supply if specified in the data sheets; any special requirements for the excluded equipment shall be given by the system vendor.
Choose an application
This standard applies to AC adjustable speed drive (ASD) systems rated over 375 kW and above 750 V output voltage as used in petrochemical and similar applications. It covers the performance requirements for an ASD system including, but not limited to, input transformer or reactor as required, power electronics, control interfaces, cooling system, switchgear, and motor. Requirements for power quality, engineering analysis, start-up assistance, training, and spare parts are also included. Certain items such as the motor, switchgear or transformer may be excluded from the scope of vendor supply if so specified in the data sheets; however the system vendor shall specify any special requirements for the equipment thus excluded.
Choose an application
Choose an application
This standard applies to AC adjustable speed drive (ASD) systems rated over 375 kW and above 750 V output voltage as used in petrochemical and similar applications. It covers the performance requirements for an ASD system including, but not limited to, input transformer or reactor as required, power electronics, control interfaces, cooling system, switchgear, and motor. Requirements for power quality, engineering analysis, start-up assistance, training, and spare parts are also included. Certain items such as the motor, switchgear or transformer may be excluded from the scope of vendor supply if so specified in the data sheets; however the system vendor shall specify any special requirements for the equipment thus excluded.
Choose an application
Choose an application
Listing 1 - 10 of 65 | << page >> |
Sort by
|