Listing 1 - 9 of 9 |
Sort by
|
Choose an application
The demands on innovative materials given by the ever-increasing requirements of contemporary industry require the use of high-performance engineering materials. The properties of materials and alloys are a result of their structures, which can primarily be affected by the preparation/production process. However, the production of materials featuring high levels of the required properties without the necessity to use costly alloying elements or time- and money-demanding heat treatment technologies typically used to enhance the mechanical properties of metallic materials (especially specific strength) still remains a challenge. The introduction of thermomechanical treatment represented a breakthrough in grain refinement, consequently leading to significant improvement of the mechanical properties of metallic materials. Contrary to conventional production technologies, the main advantage of such treatment is the possibility to precisely control structural phenomena that affect the final mechanical and utility properties. Thermomechanical treatment can only decrease the grain size to the scale of microns. However, further research devoted to pushing materials’ performance beyond the limits led to the introduction of severe plastic deformation (SPD) methods providing producers with the ability to acquire ultra-fine-grained and nanoscaled metallic materials with superior mechanical properties. SPD methods can be performed with the help of conventional forming equipment; however, many newly designed processes have also been introduced.
crack nucleation --- fatigue --- plastic deformation --- surface topography --- high-entropy alloy --- powder metallurgy --- microstructure --- spring steel --- heat treatment --- retained austenite --- Mössbauer spectroscopy --- neutron diffraction --- tungsten heavy alloy --- rotary swaging --- finite element analysis --- deformation behaviour --- residual stress --- austenitic steel 08Ch18N10T --- cyclic plasticity --- cyclic hardening --- experiments --- finite element method --- low-cycle fatigue --- tungsten --- dislocations --- microstrain --- twist channel angular pressing --- severe plastic deformation --- mechanical properties --- disintegrator --- microscopy --- wear --- high energy milling --- cement --- sintering --- quenching --- abrasive waterjet --- machining --- traverse speed --- material structure --- material properties --- cutting force --- deformation force --- clad composite --- effective strain --- heat-resistant steel --- cast steel --- microalloying --- strengthening mechanism --- abrasive water jet cutting --- surface roughness --- hardness --- tensile strength --- functional properties --- metallic systems --- mechanical processing --- structural phenomena
Choose an application
The demands on innovative materials given by the ever-increasing requirements of contemporary industry require the use of high-performance engineering materials. The properties of materials and alloys are a result of their structures, which can primarily be affected by the preparation/production process. However, the production of materials featuring high levels of the required properties without the necessity to use costly alloying elements or time- and money-demanding heat treatment technologies typically used to enhance the mechanical properties of metallic materials (especially specific strength) still remains a challenge. The introduction of thermomechanical treatment represented a breakthrough in grain refinement, consequently leading to significant improvement of the mechanical properties of metallic materials. Contrary to conventional production technologies, the main advantage of such treatment is the possibility to precisely control structural phenomena that affect the final mechanical and utility properties. Thermomechanical treatment can only decrease the grain size to the scale of microns. However, further research devoted to pushing materials’ performance beyond the limits led to the introduction of severe plastic deformation (SPD) methods providing producers with the ability to acquire ultra-fine-grained and nanoscaled metallic materials with superior mechanical properties. SPD methods can be performed with the help of conventional forming equipment; however, many newly designed processes have also been introduced.
History of engineering & technology --- crack nucleation --- fatigue --- plastic deformation --- surface topography --- high-entropy alloy --- powder metallurgy --- microstructure --- spring steel --- heat treatment --- retained austenite --- Mössbauer spectroscopy --- neutron diffraction --- tungsten heavy alloy --- rotary swaging --- finite element analysis --- deformation behaviour --- residual stress --- austenitic steel 08Ch18N10T --- cyclic plasticity --- cyclic hardening --- experiments --- finite element method --- low-cycle fatigue --- tungsten --- dislocations --- microstrain --- twist channel angular pressing --- severe plastic deformation --- mechanical properties --- disintegrator --- microscopy --- wear --- high energy milling --- cement --- sintering --- quenching --- abrasive waterjet --- machining --- traverse speed --- material structure --- material properties --- cutting force --- deformation force --- clad composite --- effective strain --- heat-resistant steel --- cast steel --- microalloying --- strengthening mechanism --- abrasive water jet cutting --- surface roughness --- hardness --- tensile strength --- functional properties --- metallic systems --- mechanical processing --- structural phenomena --- crack nucleation --- fatigue --- plastic deformation --- surface topography --- high-entropy alloy --- powder metallurgy --- microstructure --- spring steel --- heat treatment --- retained austenite --- Mössbauer spectroscopy --- neutron diffraction --- tungsten heavy alloy --- rotary swaging --- finite element analysis --- deformation behaviour --- residual stress --- austenitic steel 08Ch18N10T --- cyclic plasticity --- cyclic hardening --- experiments --- finite element method --- low-cycle fatigue --- tungsten --- dislocations --- microstrain --- twist channel angular pressing --- severe plastic deformation --- mechanical properties --- disintegrator --- microscopy --- wear --- high energy milling --- cement --- sintering --- quenching --- abrasive waterjet --- machining --- traverse speed --- material structure --- material properties --- cutting force --- deformation force --- clad composite --- effective strain --- heat-resistant steel --- cast steel --- microalloying --- strengthening mechanism --- abrasive water jet cutting --- surface roughness --- hardness --- tensile strength --- functional properties --- metallic systems --- mechanical processing --- structural phenomena
Choose an application
We live in interesting times in which life as we know it is being threatened by manmade changes to the atmosphere in which we live. On the global scale, concern is focused on climate change due to greenhouse gas emissions, and on a national scale, atmospheric pollution produced by combustion processes is of concern. A possible approach is through the development of new ideas and innovative processes to the current practices. Among the available options, multi-generation processes such as the trigeneration cycle, battery storage system, solar power plants and heat pumps have been widely studied, as they potentially allow for greater efficiency, lower costs, and reduced emissions. On the other hand, some researchers had been working to increase the potential of energy generation process through heat recovery under the steam generator, organic Rankine cycle, and absorption chillers. In this Special Issue on "Thermal Systems” of fundamental or applied and numerical or experimental investigation, many new concepts in thermal systems and energy utilization were explored and published as original research papers in this “Special Issue”.
History of engineering & technology --- thermo-economic assessment --- exergy analysis --- trigeneration system --- gas microturbine --- absorption chiller --- advanced exergo-economic analysis --- waste heat recovery system --- ORC --- endogenous exergy --- exogenous exergy --- thermal management --- Li-ion battery --- heat pipe --- thermoelectric cooler --- oscillating heat pipes --- heat transfer --- milling cooling --- abrasive-milling processes --- solar network --- dynamic modelling --- plug flow --- control --- supercritical carbon dioxide --- experimental testing --- finned-tube gas cooler --- energy poverty --- centralised heat pump --- hourly heating demand --- off-design heat pump model --- alternative process --- non-coating method --- room-temperature swaging --- pseudo-single tube (PST) --- accident-tolerant fuel (ATF) cladding --- minichannel flow boiling --- void fraction --- inverse heat transfer problem --- Trefftz method --- vortex generator --- vortex tube --- temperature separation --- the low-temperature air flow ratio (yc), inlet pressure (Pi) --- thermo-economic assessment --- exergy analysis --- trigeneration system --- gas microturbine --- absorption chiller --- advanced exergo-economic analysis --- waste heat recovery system --- ORC --- endogenous exergy --- exogenous exergy --- thermal management --- Li-ion battery --- heat pipe --- thermoelectric cooler --- oscillating heat pipes --- heat transfer --- milling cooling --- abrasive-milling processes --- solar network --- dynamic modelling --- plug flow --- control --- supercritical carbon dioxide --- experimental testing --- finned-tube gas cooler --- energy poverty --- centralised heat pump --- hourly heating demand --- off-design heat pump model --- alternative process --- non-coating method --- room-temperature swaging --- pseudo-single tube (PST) --- accident-tolerant fuel (ATF) cladding --- minichannel flow boiling --- void fraction --- inverse heat transfer problem --- Trefftz method --- vortex generator --- vortex tube --- temperature separation --- the low-temperature air flow ratio (yc), inlet pressure (Pi)
Choose an application
The demands on innovative materials given by the ever-increasing requirements of contemporary industry require the use of high-performance engineering materials. The properties of materials and alloys are a result of their structures, which can primarily be affected by the preparation/production process. However, the production of materials featuring high levels of the required properties without the necessity to use costly alloying elements or time- and money-demanding heat treatment technologies typically used to enhance the mechanical properties of metallic materials (especially specific strength) still remains a challenge. The introduction of thermomechanical treatment represented a breakthrough in grain refinement, consequently leading to significant improvement of the mechanical properties of metallic materials. Contrary to conventional production technologies, the main advantage of such treatment is the possibility to precisely control structural phenomena that affect the final mechanical and utility properties. Thermomechanical treatment can only decrease the grain size to the scale of microns. However, further research devoted to pushing materials’ performance beyond the limits led to the introduction of severe plastic deformation (SPD) methods providing producers with the ability to acquire ultra-fine-grained and nanoscaled metallic materials with superior mechanical properties. SPD methods can be performed with the help of conventional forming equipment; however, many newly designed processes have also been introduced.
History of engineering & technology --- crack nucleation --- fatigue --- plastic deformation --- surface topography --- high-entropy alloy --- powder metallurgy --- microstructure --- spring steel --- heat treatment --- retained austenite --- Mössbauer spectroscopy --- neutron diffraction --- tungsten heavy alloy --- rotary swaging --- finite element analysis --- deformation behaviour --- residual stress --- austenitic steel 08Ch18N10T --- cyclic plasticity --- cyclic hardening --- experiments --- finite element method --- low-cycle fatigue --- tungsten --- dislocations --- microstrain --- twist channel angular pressing --- severe plastic deformation --- mechanical properties --- disintegrator --- microscopy --- wear --- high energy milling --- cement --- sintering --- quenching --- abrasive waterjet --- machining --- traverse speed --- material structure --- material properties --- cutting force --- deformation force --- clad composite --- effective strain --- heat-resistant steel --- cast steel --- microalloying --- strengthening mechanism --- abrasive water jet cutting --- surface roughness --- hardness --- tensile strength --- functional properties --- metallic systems --- mechanical processing --- structural phenomena
Choose an application
We live in interesting times in which life as we know it is being threatened by manmade changes to the atmosphere in which we live. On the global scale, concern is focused on climate change due to greenhouse gas emissions, and on a national scale, atmospheric pollution produced by combustion processes is of concern. A possible approach is through the development of new ideas and innovative processes to the current practices. Among the available options, multi-generation processes such as the trigeneration cycle, battery storage system, solar power plants and heat pumps have been widely studied, as they potentially allow for greater efficiency, lower costs, and reduced emissions. On the other hand, some researchers had been working to increase the potential of energy generation process through heat recovery under the steam generator, organic Rankine cycle, and absorption chillers. In this Special Issue on "Thermal Systems” of fundamental or applied and numerical or experimental investigation, many new concepts in thermal systems and energy utilization were explored and published as original research papers in this “Special Issue”.
History of engineering & technology --- thermo-economic assessment --- exergy analysis --- trigeneration system --- gas microturbine --- absorption chiller --- advanced exergo-economic analysis --- waste heat recovery system --- ORC --- endogenous exergy --- exogenous exergy --- thermal management --- Li-ion battery --- heat pipe --- thermoelectric cooler --- oscillating heat pipes --- heat transfer --- milling cooling --- abrasive-milling processes --- solar network --- dynamic modelling --- plug flow --- control --- supercritical carbon dioxide --- experimental testing --- finned-tube gas cooler --- energy poverty --- centralised heat pump --- hourly heating demand --- off-design heat pump model --- alternative process --- non-coating method --- room-temperature swaging --- pseudo-single tube (PST) --- accident-tolerant fuel (ATF) cladding --- minichannel flow boiling --- void fraction --- inverse heat transfer problem --- Trefftz method --- vortex generator --- vortex tube --- temperature separation --- the low-temperature air flow ratio (yc), inlet pressure (Pi) --- n/a
Choose an application
We live in interesting times in which life as we know it is being threatened by manmade changes to the atmosphere in which we live. On the global scale, concern is focused on climate change due to greenhouse gas emissions, and on a national scale, atmospheric pollution produced by combustion processes is of concern. A possible approach is through the development of new ideas and innovative processes to the current practices. Among the available options, multi-generation processes such as the trigeneration cycle, battery storage system, solar power plants and heat pumps have been widely studied, as they potentially allow for greater efficiency, lower costs, and reduced emissions. On the other hand, some researchers had been working to increase the potential of energy generation process through heat recovery under the steam generator, organic Rankine cycle, and absorption chillers. In this Special Issue on "Thermal Systems” of fundamental or applied and numerical or experimental investigation, many new concepts in thermal systems and energy utilization were explored and published as original research papers in this “Special Issue”.
thermo-economic assessment --- exergy analysis --- trigeneration system --- gas microturbine --- absorption chiller --- advanced exergo-economic analysis --- waste heat recovery system --- ORC --- endogenous exergy --- exogenous exergy --- thermal management --- Li-ion battery --- heat pipe --- thermoelectric cooler --- oscillating heat pipes --- heat transfer --- milling cooling --- abrasive-milling processes --- solar network --- dynamic modelling --- plug flow --- control --- supercritical carbon dioxide --- experimental testing --- finned-tube gas cooler --- energy poverty --- centralised heat pump --- hourly heating demand --- off-design heat pump model --- alternative process --- non-coating method --- room-temperature swaging --- pseudo-single tube (PST) --- accident-tolerant fuel (ATF) cladding --- minichannel flow boiling --- void fraction --- inverse heat transfer problem --- Trefftz method --- vortex generator --- vortex tube --- temperature separation --- the low-temperature air flow ratio (yc), inlet pressure (Pi) --- n/a
Choose an application
This book derives from the Special Issue of the Manufacturing Engineering Society 2019 (SIMES-2019) that has been launched as a joint issue of the journals Materials and Applied Sciences. The 29 contributions published in this Special Issue of Materials present cutting-edge advances in the field of manufacturing engineering focusing on additive manufacturing and 3D printing; advances and innovations in manufacturing processes; sustainable and green manufacturing; manufacturing of new materials; metrology and quality in manufacturing; industry 4.0; design, modeling, and simulation in manufacturing engineering; and manufacturing engineering and society. Among them, the topic "Additive Manufacturing and 3D Printing" has attracted a large number of contributions in this journal due to its widespread popularity and potential.
History of engineering & technology --- Bayesian inference --- control chart --- dynamic methodology --- hidden Markov chain --- occupational accident --- risk assessment --- risk control --- risk management --- Fused Deposition Modeling --- roughness --- Polylactic Acid --- print orientation angle --- build angle --- titanium alloys --- sustainable lubrication --- cryogenic lubrication --- MQL --- OD grinding --- CBN --- dressing --- rotary dresser --- wear --- CVD diamond --- additive manufacturing --- 3D printing --- fused filament fabrication --- flexural properties --- fatigue --- PLA --- cements --- ballast waste --- cornubianite --- mechanical properties --- Spain --- joining --- forming --- sheet–tube connections --- experimentation --- modelling and simulation --- quality enhancement --- process parameters --- design optimization --- calibration artifact --- kinematic support --- dimensional metrology --- machine tool --- length measurement --- rapid prototyping --- efficiency --- printing time --- experimental model --- prepeg --- carbon fiber --- Raman spectroscopy --- AWJM --- waterjet --- CFRP --- kerf taper --- surface quality --- metal forming --- bi-metallic --- cylinders --- compression --- finite elements --- microscopy --- cold expansion --- mandrel --- cold-forming --- swaging --- shipbuilding --- LARG paradigm --- supply chain --- coordinate metrology --- confocal microscopy --- measurement --- calibration --- traceability --- uncertainty --- quality assessment --- digital image correlation --- indentation process --- incremental forming --- finite element method --- material flow --- AWJM (Abrasive waterjet machining) --- CFRTP (Carbon fiber-reinforced thermoplastics) --- RSM (response surface methodology) --- ANOVA (Analysis of variance) --- C/TPU (carbon/polyurethane) --- image processing --- position control --- accuracy --- micromachines --- position compensation --- inverse conical perspective --- micromanufacturing --- manufacturing systems --- mechatronics --- FDM --- bimodulus materials --- standards --- finite element analysis (FEA) --- ABS --- anisotropy --- infill density --- layer orientation --- ASTM D638–14:2014 --- ISO 527–2:2012 --- grounding electrodes in two-layered soils --- step and touch potentials --- step potentials upper bound --- orthoses --- prostheses --- fused deposition modeling --- laminated object manufacturing --- selective laser sintering --- laser tracker --- Monte Carlo method --- verification --- green manufacturing --- sustainability metrics --- cleaner product life cycle --- material removal processes --- hybrid components --- light alloys --- magnesium --- aluminum --- drilling --- dry machining --- cold compressed air --- lubrication and cooling systems --- arithmetical mean roughness --- Ra --- average maximum height --- Rz --- repair and maintenance operations --- fused deposition modelling --- composites --- polymer injection moulding --- polyamide --- metal matrix composite --- Al-SiC --- microstructure --- machining --- cooling compressed air --- thrust force --- energy --- material removed rate --- PEEK-GF30 --- multi-response optimization --- sustainable manufacturing --- metrology --- industry 4.0 --- modeling and simulation --- quality in manufacturing --- technological and industrial heritage --- Bayesian inference --- control chart --- dynamic methodology --- hidden Markov chain --- occupational accident --- risk assessment --- risk control --- risk management --- Fused Deposition Modeling --- roughness --- Polylactic Acid --- print orientation angle --- build angle --- titanium alloys --- sustainable lubrication --- cryogenic lubrication --- MQL --- OD grinding --- CBN --- dressing --- rotary dresser --- wear --- CVD diamond --- additive manufacturing --- 3D printing --- fused filament fabrication --- flexural properties --- fatigue --- PLA --- cements --- ballast waste --- cornubianite --- mechanical properties --- Spain --- joining --- forming --- sheet–tube connections --- experimentation --- modelling and simulation --- quality enhancement --- process parameters --- design optimization --- calibration artifact --- kinematic support --- dimensional metrology --- machine tool --- length measurement --- rapid prototyping --- efficiency --- printing time --- experimental model --- prepeg --- carbon fiber --- Raman spectroscopy --- AWJM --- waterjet --- CFRP --- kerf taper --- surface quality --- metal forming --- bi-metallic --- cylinders --- compression --- finite elements --- microscopy --- cold expansion --- mandrel --- cold-forming --- swaging --- shipbuilding --- LARG paradigm --- supply chain --- coordinate metrology --- confocal microscopy --- measurement --- calibration --- traceability --- uncertainty --- quality assessment --- digital image correlation --- indentation process --- incremental forming --- finite element method --- material flow --- AWJM (Abrasive waterjet machining) --- CFRTP (Carbon fiber-reinforced thermoplastics) --- RSM (response surface methodology) --- ANOVA (Analysis of variance) --- C/TPU (carbon/polyurethane) --- image processing --- position control --- accuracy --- micromachines --- position compensation --- inverse conical perspective --- micromanufacturing --- manufacturing systems --- mechatronics --- FDM --- bimodulus materials --- standards --- finite element analysis (FEA) --- ABS --- anisotropy --- infill density --- layer orientation --- ASTM D638–14:2014 --- ISO 527–2:2012 --- grounding electrodes in two-layered soils --- step and touch potentials --- step potentials upper bound --- orthoses --- prostheses --- fused deposition modeling --- laminated object manufacturing --- selective laser sintering --- laser tracker --- Monte Carlo method --- verification --- green manufacturing --- sustainability metrics --- cleaner product life cycle --- material removal processes --- hybrid components --- light alloys --- magnesium --- aluminum --- drilling --- dry machining --- cold compressed air --- lubrication and cooling systems --- arithmetical mean roughness --- Ra --- average maximum height --- Rz --- repair and maintenance operations --- fused deposition modelling --- composites --- polymer injection moulding --- polyamide --- metal matrix composite --- Al-SiC --- microstructure --- machining --- cooling compressed air --- thrust force --- energy --- material removed rate --- PEEK-GF30 --- multi-response optimization --- sustainable manufacturing --- metrology --- industry 4.0 --- modeling and simulation --- quality in manufacturing --- technological and industrial heritage
Choose an application
This book derives from the Special Issue of the Manufacturing Engineering Society 2019 (SIMES-2019) that has been launched as a joint issue of the journals Materials and Applied Sciences. The 29 contributions published in this Special Issue of Materials present cutting-edge advances in the field of manufacturing engineering focusing on additive manufacturing and 3D printing; advances and innovations in manufacturing processes; sustainable and green manufacturing; manufacturing of new materials; metrology and quality in manufacturing; industry 4.0; design, modeling, and simulation in manufacturing engineering; and manufacturing engineering and society. Among them, the topic "Additive Manufacturing and 3D Printing" has attracted a large number of contributions in this journal due to its widespread popularity and potential.
History of engineering & technology --- Bayesian inference --- control chart --- dynamic methodology --- hidden Markov chain --- occupational accident --- risk assessment --- risk control --- risk management --- Fused Deposition Modeling --- roughness --- Polylactic Acid --- print orientation angle --- build angle --- titanium alloys --- sustainable lubrication --- cryogenic lubrication --- MQL --- OD grinding --- CBN --- dressing --- rotary dresser --- wear --- CVD diamond --- additive manufacturing --- 3D printing --- fused filament fabrication --- flexural properties --- fatigue --- PLA --- cements --- ballast waste --- cornubianite --- mechanical properties --- Spain --- joining --- forming --- sheet–tube connections --- experimentation --- modelling and simulation --- quality enhancement --- process parameters --- design optimization --- calibration artifact --- kinematic support --- dimensional metrology --- machine tool --- length measurement --- rapid prototyping --- efficiency --- printing time --- experimental model --- prepeg --- carbon fiber --- Raman spectroscopy --- AWJM --- waterjet --- CFRP --- kerf taper --- surface quality --- metal forming --- bi-metallic --- cylinders --- compression --- finite elements --- microscopy --- cold expansion --- mandrel --- cold-forming --- swaging --- shipbuilding --- LARG paradigm --- supply chain --- coordinate metrology --- confocal microscopy --- measurement --- calibration --- traceability --- uncertainty --- quality assessment --- digital image correlation --- indentation process --- incremental forming --- finite element method --- material flow --- AWJM (Abrasive waterjet machining) --- CFRTP (Carbon fiber-reinforced thermoplastics) --- RSM (response surface methodology) --- ANOVA (Analysis of variance) --- C/TPU (carbon/polyurethane) --- image processing --- position control --- accuracy --- micromachines --- position compensation --- inverse conical perspective --- micromanufacturing --- manufacturing systems --- mechatronics --- FDM --- bimodulus materials --- standards --- finite element analysis (FEA) --- ABS --- anisotropy --- infill density --- layer orientation --- ASTM D638–14:2014 --- ISO 527–2:2012 --- grounding electrodes in two-layered soils --- step and touch potentials --- step potentials upper bound --- orthoses --- prostheses --- fused deposition modeling --- laminated object manufacturing --- selective laser sintering --- laser tracker --- Monte Carlo method --- verification --- green manufacturing --- sustainability metrics --- cleaner product life cycle --- material removal processes --- hybrid components --- light alloys --- magnesium --- aluminum --- drilling --- dry machining --- cold compressed air --- lubrication and cooling systems --- arithmetical mean roughness --- Ra --- average maximum height --- Rz --- repair and maintenance operations --- fused deposition modelling --- composites --- polymer injection moulding --- polyamide --- metal matrix composite --- Al-SiC --- microstructure --- machining --- cooling compressed air --- thrust force --- energy --- material removed rate --- PEEK-GF30 --- multi-response optimization --- sustainable manufacturing --- metrology --- industry 4.0 --- modeling and simulation --- quality in manufacturing --- technological and industrial heritage
Choose an application
This book derives from the Special Issue of the Manufacturing Engineering Society 2019 (SIMES-2019) that has been launched as a joint issue of the journals Materials and Applied Sciences. The 29 contributions published in this Special Issue of Materials present cutting-edge advances in the field of manufacturing engineering focusing on additive manufacturing and 3D printing; advances and innovations in manufacturing processes; sustainable and green manufacturing; manufacturing of new materials; metrology and quality in manufacturing; industry 4.0; design, modeling, and simulation in manufacturing engineering; and manufacturing engineering and society. Among them, the topic "Additive Manufacturing and 3D Printing" has attracted a large number of contributions in this journal due to its widespread popularity and potential.
Bayesian inference --- control chart --- dynamic methodology --- hidden Markov chain --- occupational accident --- risk assessment --- risk control --- risk management --- Fused Deposition Modeling --- roughness --- Polylactic Acid --- print orientation angle --- build angle --- titanium alloys --- sustainable lubrication --- cryogenic lubrication --- MQL --- OD grinding --- CBN --- dressing --- rotary dresser --- wear --- CVD diamond --- additive manufacturing --- 3D printing --- fused filament fabrication --- flexural properties --- fatigue --- PLA --- cements --- ballast waste --- cornubianite --- mechanical properties --- Spain --- joining --- forming --- sheet–tube connections --- experimentation --- modelling and simulation --- quality enhancement --- process parameters --- design optimization --- calibration artifact --- kinematic support --- dimensional metrology --- machine tool --- length measurement --- rapid prototyping --- efficiency --- printing time --- experimental model --- prepeg --- carbon fiber --- Raman spectroscopy --- AWJM --- waterjet --- CFRP --- kerf taper --- surface quality --- metal forming --- bi-metallic --- cylinders --- compression --- finite elements --- microscopy --- cold expansion --- mandrel --- cold-forming --- swaging --- shipbuilding --- LARG paradigm --- supply chain --- coordinate metrology --- confocal microscopy --- measurement --- calibration --- traceability --- uncertainty --- quality assessment --- digital image correlation --- indentation process --- incremental forming --- finite element method --- material flow --- AWJM (Abrasive waterjet machining) --- CFRTP (Carbon fiber-reinforced thermoplastics) --- RSM (response surface methodology) --- ANOVA (Analysis of variance) --- C/TPU (carbon/polyurethane) --- image processing --- position control --- accuracy --- micromachines --- position compensation --- inverse conical perspective --- micromanufacturing --- manufacturing systems --- mechatronics --- FDM --- bimodulus materials --- standards --- finite element analysis (FEA) --- ABS --- anisotropy --- infill density --- layer orientation --- ASTM D638–14:2014 --- ISO 527–2:2012 --- grounding electrodes in two-layered soils --- step and touch potentials --- step potentials upper bound --- orthoses --- prostheses --- fused deposition modeling --- laminated object manufacturing --- selective laser sintering --- laser tracker --- Monte Carlo method --- verification --- green manufacturing --- sustainability metrics --- cleaner product life cycle --- material removal processes --- hybrid components --- light alloys --- magnesium --- aluminum --- drilling --- dry machining --- cold compressed air --- lubrication and cooling systems --- arithmetical mean roughness --- Ra --- average maximum height --- Rz --- repair and maintenance operations --- fused deposition modelling --- composites --- polymer injection moulding --- polyamide --- metal matrix composite --- Al-SiC --- microstructure --- machining --- cooling compressed air --- thrust force --- energy --- material removed rate --- PEEK-GF30 --- multi-response optimization --- sustainable manufacturing --- metrology --- industry 4.0 --- modeling and simulation --- quality in manufacturing --- technological and industrial heritage
Listing 1 - 9 of 9 |
Sort by
|